HAWE比例調壓閥技術特性，哈威比例調壓閥材質壽命[產品打印頁面]

HAWE比例調壓閥技術特性，哈威比例調壓閥材質壽命
Pressure regulator can be said that the basic pressure relief valve, the working principle of the valve as follows:
High-pressure medium through a small hole into a relatively large cavity to achieve decompression,
In fact, by blocking the pressure, the diaphragm or piston on both sides of the mouth is the outlet,
主要作為執行機構的預調節閥,可達19bar 
此壓差＝PA-PR,并與比例電磁鐵的電流成比例變化.
通過出口A處的壓力PA可以操縱液壓執行機構,并可實現對對變量泵,比例閥等的無級調節.
比例電磁鐵的功率需求非常低,
樣本D78817/1,D7831/1或D7835中的EV型放大器以及D7845 FF 中的PLVC型可編程總線控制器可以作為控制裝置。
P口處允許進口壓力(系統壓力)被限制在40bar,在較高壓力情況下,
為避免慣性時間后的調節不準確以及切換跳躍,需將壓力預先降低至PP＝40bar。

 單閥訂貨實例;PM11-7-B0,6-G24/1
閥組訂貨實例;PMZ1A51-11/1-11/1-1-G24
One side is man-made pressure, and control the size of the stem and the diaphragm (piston) connected,
So as long as a fixed pressure, then the pressure of the outlet chamber will always be equal to this pressure,
This given pressure can be provided by a spring or air source or hydraulic source.
壓力差Pmax=19 bar
流量Qmax=2 lpm
概述
PM和PMZ型調壓閥為鋼制直動式調壓閥,由閥體,調節閥心,閥套和比例電磁鐵構成。
 它能將由P口處進入的不穩定的系統壓力在閥出口A處降低為一個較低的,恒定的壓力差。
調壓閥基本可以說是減壓閥，減壓閥的工作原理如下：
高壓介質通過一個小孔充到一個相對較大的腔里實現減壓，
This differential pressure = PA-PR,
and with the proportional electromagnet current proportional change.
The pressure PA at the outlet A can be operated by the hydraulic actuator and
the stepless adjustment of the variable pump, proportional valve, etc. can be achieved.
Proportional electromagnet power requirements are very low,

HAWE比例調壓閥技術特性，哈威比例調壓閥材質壽命

產品留言

標題

聯系人

聯系電話

內容

驗證碼

點擊換一張

注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
2.如有必要,請您留下您的詳細聯系方式!